Technical Specifications) Parameter Specification / Typical Value Manufacturer / Brand Eaton Model Number LZMB1 Product Line NZM Device Type Electronic Trip Unit Rated Supply Voltage Typically powered by the current transformers within the breaker (self-powered) or with an auxiliary power supply option. Protection Functions L - Long-time Delay (Overload) S - Short-time Delay I - Instantaneous G - Ground-fault Adjustability Yes. Current settings (Ir, Isd, Ii, Ig) and time delays (tr, tsd) are fully adjustable via dials or an interface. Display & Indication Typically an LCD or LED display for current, status, and fault information. Communication Ready Often designed to be the base unit for adding communication modules (e.g., for Profibus, Modbus, Ethernet/IP). Compatible Breaker Frame Sizes Designed for specific NZM frame sizes (e.g., NZM2, NZM3, NZM4). 必须与断路器本体匹配。 Standards Compliance As part of the complete breaker, it helps comply with IEC 60947-2 and other relevant standards.

Technical Specifications Parameter Specification / Typical Value Manufacturer / Brand Eaton Model Number LZMN1-A20 Product Line NZM Rated Current (Iₙ) 20 A Poles 3 Frame Size NZM1-A Rated Operational Voltage (Uₑ) 400/415 V AC (IEC) / 690 V AC Rated Insulation Voltage (Uᵢ) 690 V AC Rated Frequency 50/60 Hz Rated Ultimate Breaking Capacity (I꜀ᵤ) Typically 25 kA / 36 kA @ 400V (Must be verified from datasheet) Trip Unit Type Thermal-Magnetic (Non-Adjustable) Overload Protection (Ir) Fixed at 20A Short-Circuit Protection (Im) Fixed magnetic trip Installation Fixed Type Standards Compliance IEC 60947-2 Electrical Life Several thousand cycles (e.g., 5,000) Mechanical Life Tens of thousands of cycles (e.g., 20,000) Terminal Torque Refer to official manual (e.g., ~ 6 N·m)

Technical Specifications Parameter Specification / Typical Value Manufacturer / Brand Eaton Model Number LZMC200A Product Line xEffect Molded Case Circuit Breaker (MCCB) Rated Current (Iu) 200 A Poles 3 Rated Operational Voltage (Ue) 400/415 V AC (IEC) 480 V AC (UL) Rated Insulation Voltage (Ui) 690 V AC Rated Frequency 50/60 Hz Rated Ultimate Breaking Capacity (Icu) @ ...V e.g., 25 kA / 35 kA / 50 kA (This is a CRITICAL detail that varies by specific model suffix and must be verified) Rated Service Breaking Capacity (Ics) Typically a percentage of Icu (e.g., 100% or 75%) Trip Unit Type Thermal-Magnetic (TMD) or Electronic (MPU) Overload Protection (Ir) Adjustable on electronic versions (e.g., 0.4 - 1 x In) Short-Circuit Protection (Im) Adjustable on electronic versions Installation Fixed Type (or can be mounted on a fixed base) Terminal Type Stud type or Cable Lug (for larger conductors) Standards Compliance IEC 60947-2, GB 14048.2, (May also have UL 489) Torque Specification As per manufacturer's manual (e.g., 35-50 N·m for main terminals)

Technical Specifications Parameter Specification Model Series EZ Valve Size 1 inch (DN25) Pressure Class 150 LB (ANSI B16.5) End Connections Screwed (NPT) or Flanged (configuration dependent) Inlet Pressure Range Up to 250 psig (17.2 bar) (typical) Outlet Pressure Range Field-adjustable (e.g., 5–60 psig or other spring-dependent range) Flow Characteristic Self-operated (spring vs. diaphragm force balance) Body Material Cast Iron (standard) Trim Material Stainless Steel (standard) Diaphragm Material Buna-N (standard) Temperature Range -20°F to 180°F (-29°C to 82°C)

Technical Parameters Parameter Value / Description Manufacturer Fisher (Emerson Process Management) Product Series DVC2000 Series Digital Valve Controller Fisher Model 17A5515X012 Universal Model DVC2000 Action Direct Acting (Increase in input signal causes increase in output pressure). Actuator Type Single-Acting (Non-Interspring). For spring-return or single-acting piston actuators. Supply Pressure Typically up to 150 psig (10.3 bar). Output Pressure Up to the supply pressure limit. Input Signal 4-20 mA DC, with HART protocol digital superimposition. Supply Port 1/4 in. NPT (Female) Output Port 1/4 in. NPT (Female) Signal Port 1/2 in. NPT (Conduit connection) Air Consumption Low steady-state consumption (typically < 0.2 SCFM / 0.005 Nm³/min). Air Flow Capacity High capacity for fast valve stroking. Enclosure Rating NEMA 4X (IP66). Weatherproof, watertight, and corrosion-resistant. Ambient Temperature Standard: -40°F to 185°F (-40°C to 85°C). Vibration Resistance Up to 2.5 g from 10 to 150 Hz. Mounting Direct mount on Fisher rotary and linear actuators using appropriate mounting kits. Communication Protocol HART (Highway Addressable Remote Transducer) Protocol, Version 5, 6, or 7.

Technical Specifications Parameter Specification Model 12P1731X032 Type Control Valve Assembly Valve Style Globe Valve Valve Size Likely 1.5 inch (encoded in "1731") Pressure Class ANSI Class 150 or 300 (encoded in model number) Actuator Type Pneumatic Spring-Diaphragm ("X032" configuration) Actuator Action Spring-Return (fail-safe) Air Signal 3-15 psig (0.2-1.0 bar) standard Flow Characteristic Equal Percentage or Linear (trim dependent) End Connections Flanged (RF facing standard) Body Material Carbon Steel (WCB) standard Trim Material Stainless Steel standard Temperature Range -20°F to 450°F (-29°C to 232°C) standard

Parameters / Specifications Based on the 67C Series general data and typical 67CFR variants, the likely specifications for the PF‑67CFR‑P262 are: Model: Fisher PF‑67CFR‑P262 Series: Fisher 67C Series Instrument Supply Regulators Construction Type: Direct‑operated regulator with filter and internal relief valve (67CFR) Body Material: Aluminum alloy (standard for non‑stainless versions) End Connections / Body Size: ¼‑inch NPT for inlet and outlet (standard for 67C Series) Maximum Inlet Pressure (Body Rating): 250 psig (≈17.2 bar) for aluminum body version (all except stainless) Maximum Emergency Outlet Pressure (Relief Margin): 50 psig (≈3.4 bar) above the set outlet pressure Temperature Capability (depending on elastomer/filter selection): Nitrile (NBR): approx. –40 °F to +180 °F (≈ –40 °C to +82 °C) Fluoroelastomer (FKM): approx. 0 °F to +300 °F (≈ –18 °C to +149 °C) Silicone (VMQ) diaphragm with low‑temperature bolting: approx. –60 °F to +180 °F (≈ –51 °C to +82 °C) Media: Clean instrument air or compatible gases (assuming material compatibility) Features: Filter cartridge included (part of the “F”), internal relief valve (part of the “R”), compact size, panel or inline mount capability Approximate Weight: ~1 lb (~0.5 kg) for the ¼‑in NPT aluminum body version Note: The exact outlet (regulated) pressure spring range for the “P262” suffix is not explicitly published in the general catalogue; typical spring ranges in the 67C Series include 0‑20 psig, 0‑35 psig, 0‑60 psig, 0‑125 psig, etc. Additional technical data: The regulator offers excellent inlet‐sensitivity performance (e.g., less than 0.2 psig change in outlet for 25 psig change in inlet) and repeatability approx. 0.1 psig depending on elastomer. Typical Applications: Instrumentation supply regulators for pneumatic controllers, valve positioners, air chucks, instrumentation panels.

Technical Specifications Category Specification Model 4160K Type Pneumatic Force-Balance, Displacer-Type Measurement Principle Buoyancy Output Signal 3 to 15 psig (0.2 to 1.0 bar) Supply Air Pressure 20 psig (1.4 bar) minimum, 35 psig (2.4 bar) maximum. A 20-35 psig supply is required for proper operation. Air Consumption Approximately 0.5 SCFM (14 standard liters per minute) at maximum output. Span Adjustment Typically from 5 to 50 inches (127 to 1270 mm) of H₂O buoyancy force. Adjustable via range spring. Zero Adjustment External adjustment provided. Accuracy Typically ±0.5% of span. Repeatability Typically ±0.1% of span. Materials of Construction Body/Bonnet: Cast Iron or Ductile Iron (epoxy coated). Internals & Displacer: 316 Stainless Steel standard; other materials like Monel, Hastelloy available. Process Connections Body: 2-inch NPT standard. Displacer Chamber: 1½-inch or 2-inch NPT, or flanged options (e.g., 150# RF). Ambient Temperature Limit -20° to +150°F (-29° to +66°C) Process Temperature Limit Up to +750°F (+399°C) with extended bonnet and appropriate seals. Approvals Intrinsically safe for Class I, Division 1, Groups B, C, and D hazardous locations. (Commonly approved by FM, CSA, etc.).

Category Specification Fisher Part Number 627-1217-29855 Description Trim & Plug Kit Assembly Applicable Valve Series Fisher ED, EDT, ES, EST, ET Series Eccentric Rotary Valves Trim Type Eccentric Rotary Plug Trim Plug Type Standard Eccentric Plug Flow Characteristic Standard (Approximately Equal Percentage) Primary Material Plug (Valve Ball): Hardened 17-4PH Stainless Steel Sleeve/Seat: Typically 17-4PH SS or 316 SS Hardness Plug is heat-treated (hardened) for enhanced wear and cavitation resistance. Seat Leakage Classification When assembled with a compatible seat, typically meets ANSI Class IV (0.01% of rated capacity) or better. Typical Service General service for liquids, gases, and steam. Ideal for applications requiring good shut-off and erosion resistance.

Category Specification Model Y690AM-22 Type Pneumatic Spring-Diaphragm Actuator (Specifically, a Piston-Type for Rotary Valves) Action Reverse Action (A) & Double-Acting (M) • Reverse Action: Stem retracts with increasing air signal. • Double-Acting: Requires air pressure to both open and close the valve. It has no spring and is not fail-safe. Standard Air Signal 3 to 15 psig (0.2 to 1.0 bar) Supply Air Pressure Maximum 100 psig (6.9 bar) supply pressure. The actual torque output is directly proportional to the supply pressure used. Travel Standard travel is 90 degrees of rotation, suitable for quarter-turn valves. Mounting Designed for direct mounting to Fisher V100, V150, V500, and other compatible rotary valve series via a standardized bracket. Typical Torque Output The Y690A size provides a specific torque range. For precise torque values at different air pressures, you must consult the official Fisher torque chart. (e.g., With 100 psig air supply, the torque output can be in the range of several hundred lb-in). Diaphragm / Piston Material Nitrile (Buna-N) is standard for elastomers; other materials are available for different temperatures and services. Housing Material Cast aluminum or ductile iron, with a corrosion-resistant coating. Temperature Limits Standard elastomers are suitable for temperatures between -20° to +180°F (-29° to +82°C).